จาระบีสำหรับลูกปืนล้อ งานเพลา Red Line High Performance Racing Grade CV-2 Grease
CV-2 Grease Synthetic
จารบีเอนกประสงค์พื้นฐานใช่ในงานเพลา งานลูกปืนล้อ จัดอยู่ในเกรด NLGI #2 หรือที่เขาให้คำจำกัดความว่า จารบีปกติ หรือ หนืดเหมือน เนยถั่ว
Drop point มากกว่า 800 องศาฟาเรนไฮ
-เหมาะสำหรับ ลูกปืนและเพลาขับ CV- Joint ที่ต้องทนความร้อนสูง
- จารบีเบส PAO+Polyolester
- ทนความร้อนสูง อุณหภูมิใช้งานจาก0-426C
- ป้องกันการสึกหรอได้สูง และคงสภาพที่อุณหภูมิความร้อนสูงได้ดีกว่าทั่วไป
Redline High Performance Racing Grade Red Line CV-2 Grease
- Made of good material
- Good design
- Good Product
CV-2 Grease
Outperforms the best conventional or synthetic greases and lubes
Withstands extreme temperature and pressure in wheel bearings U-joints and high-angle CV Joints
Excellent high-temp stability extreme-pressure protection and water resistance
Used in a variety of applications with operating temps from -100°F to 500°F
Strong resistance to oxidation and corrosion low evaporation and oil separation with a minimum effect on rubber seals
Contains an organic moly for chassis lubrication and high temp/high speed industrial equipment
Synthetic fluidity allows increases in bearing life up to 200%
Will darken after high-temp use-not detrimental to performance
ABOUT RED LINE GREASE AND ASSEMBLY LUBE
Used by many of the best engine builders engineers and technicians in Formula 1 GP2 Formula 3 NASCAR NHRA and WRC
TYPICAL PROPERTIES
4-Ball Wear (ASTM D-4172B) 0.46
4-Ball Weld (ASTM D-2783) 400 Kg
Load/Wear Index (ASTM D-2783) 71.1
Drop Point 900°F+
MORE TECHNICAL INFORMATION
Lubricant 4-Ball Wear Load/WearIndex
(ASTM D-4172B) (ASTM D-2783)
Red Line CV-2 0.46 71.1
Syn Grease - M 0.50 41.9
Syn Moly Grease - A 0.78 38.4
GM Wheel Bearing Grease 0.71 36.6
Lubricant 4-Ball Weld Drop Point
(ASTM D-2783)
Red Line CV-2 400 Kg 900°F+
Syn Grease - M 2 200 Kg 485°F
Syn Moly Grease - A 315 Kg 515°F
GM Wheel Bearing Grease 250 Kg 525°F
PROPERTY CV-2 GREASE
NLGI Grade # 2
NLGI Service GC-LB
Thickener Non-Soap
Fluid Type Thermally-stable synthetic
Useful Temperature Range -100°F to 500°F
Color Red
Dropping Point °F 900+
Load Wear Index 71.2
4-Ball Wear Scar Diameter (Red) 40 Kg 0.46 mm
Water Washout @ 105°F 1%
Evaporation Loss 22 hrs @ 350°F 4%
Oil Separation 30 hrs @ 350°F 5%
Oxidation Stability 500 hrs @210°F psi 12
Rust Test ASTM D1743 Pass
Red Line CV-2 Grease is designed to withstand the extreme temperatures and pressures
which occur in high-performance wheel bearings and CV-joints. The excellent hightemperature
stability extreme-pressure protection and water resistance enables it to
out-perform even the best conventional or synthetic greases. Red Line CV-2 Grease can be
used in a wide range of applications at temperatures ranging between -100°F to 500°F and
provides good oxidation and corrosion resistance low evaporation and oil separation and has
a minimum effect on rubber seals. The exceptional extreme-pressure performance and the
fluidity of the synthetic oil allows increases in bearing life of 200% to 800%. Red Line CV-2
Grease contains a red moly compound which is a superior lubricant to black moly disulfide
lubricants.
Red Line CV-2 Grease may also be used in industrial applications such as high-temperature
alternator bearings high-speed ball bearings conveyor bearings worm gear drives servo
mechanisms and applications where vibrations can cause fretting wear and corrosion to take
place.
Red Line CV-2 Grease will retain its consistency and extreme-pressure performance under
high-temperature and high-shear conditions for extended periods which extends the
performance ranges of the lubricated components. Red Line CV-2 will slightly darken after
high-temperature use; this darkening will not detrimentally effect the performance of the
grease. Although Red Line CV-2 is compatible with small amounts of many petroleum-based
greases it is always good lubrication practice to thoroughly clean out the old grease to
eliminate abrasive particles and to minimize the possibility of grease incompatibility
#RedLine